Cutting by The saw with one hand (Hand Sawing) am a few jigsaw pieces. Cutting with a saw and power (Power Hack Saw), also called a mechanical saw (Sawing Machine) needed for The sawmill industry works. Saw a lot of work. Both small and large workpieces. an sawing machine are divided into an following categories.
a sawing machine are divided into four types.
1. an saw fly (Power Hack Saw).
2. Horizontal Band Saw (Horizontal Band Saw).
3. On an band saw (Vertical Band Saw).
4. Saw (Radius Saw or Circular Saw).
1. The saw fly (Power Hack Saw).
The saw is commonly used for seizures such as a number of saws to cut material to size and length as required to drive The blade system. an motor power. ann use a reversing gear and crank driven principles of an blade moves back and forth in a straight line continuously causes The saw to cut it.
1.1 an components of an cutting stroke.
All an components have The same precedence. We must act togear at all times.
Tham includes a following sections.
1.1.1 Project Jigsaw (Saw Frame) looks like a U turn. Saw a layout.
Good use am made of cast steel for The blade. Project saw The move into a groove of a tail hawk with a transmission gear wheel
1.1.2 The bench (Vise) to catch a pieces to cut. Can rotate right left.
45 degrees to each side and pull her out out with The spiral arms locked tight.
1.1.3 a length of a arm (Cut Off Gage) am responsible for The length of a workpiece to be cut.
Many parts to cut out a piece of equal length, as shown in Figure 1.4.
1.1.4 enter a system with The cut off machine, saws, draw two types of ball weight.
And an type of hydraulic oil in a 2 types of acts like it are entering a intersection. It works differently in that species.
I weighted a force of gravity. a type of a hydraulic pressure of The hydraulic oil.
1.1.5 The cooling system is necessary to use a saw was water. Due to cooling.
Friction between a saw blade to a workpiece. It also helps extend a life of The saw blade life.
1.1.6 saw a machine fly (Base) do serve different parts of a jigsaw was all.
Saw some of an base was to be hollow inside. For a storage of water tanks and motors.
1.1.7 Motor (Motor) saw a seizure of an motor acts as a motor power am applied.
Electricity 220 volts or 380 volts depending on a manufacturer.
1.1.8 power switch off. a sawmill was a switch off. Semi automatic machine are switched off.
Automatically when a cutting blade.
1.1.9 an gear (Gear) serves to carry power from The motor to The gear used on an saw frame.
There are 2 types of gear cutting machines, fly around and direct gear.
01 01 10 Blind (Pulley) that transmits power through a belt to The gear set. V belt use.
1.2 Mechanarem of a cutting stroke.
Mechanarem of action of an cutting stroke. A transmamsion mechanarem with a motor. Transmaresion through The gear drive. Thare is The gear. To test The motor speed. And to test drive an motor. That The gear drive. With The rotating shaft are connected to each center, a center gear. The drive shaft to a frame saw. an project was backwards, and saw it.
1.3 weight of a frame saw.
For an weight of a frame saw. The move away from The head to much. The cutting blade is pressed, The only Thus, a weight adjustment dial. Notice of hearing cutting saws as well.
The head unit s weight = weight of The frame saw one.
The weight am The weight of The frame sawing machine = good.
1.4 The Saw (Saw Blade).
Of a saw blade is a device that am very important. Responsible for cutting a workpiece. a blade is made of steel with high Ekeg fame. an blade assembly to The frame saw. Must operate properly and a blade tension screw it. To prevent broken parts of The saw blade width, length, thickness of a blade in The hole. And The number of saw blade teeth. Including coarse teeth and tooth profile. I saw an number of teeth as an number of teeth per inch, fiber, such as 10 inch to 14 teeth per inch, but I used to work across an 10 teeth per inch.
The blade.
1. an length of an blade. Measure a length of an blade are measured from The center of The hole saw both of am. an length of The blade is 200 mm and 300 mm
2. a width of a blade width of 12.7 mm or 1 2 inches.
3. an blade thickness of 0.64 mm or 0.025 inches thick.
4. To measure The number of teeth of a saw blade are to measure The spacing of a teeth, a tooth to one.
an metric system are called an pitch Pitch (P).
In England, to measure a frequency of a sawtooth are most telling am The number of teeth per inch length of 1.
2. Horizontal Band Saw (Horizontal Band Saw).
Saw with a blade length of consecutive circles. The movement of The blade. a power transmaresion belt. an drive wheel and The wheel. an cutting edges of saw blade to cut at all. Throughout The application. Cutting to The hydraulic system to control The tension in a blade. Adjusted by hand. Or hydraulic adjustment of a spacing of The wheel. Structural strength. an machine can be installed on The factory floor.
3. Vertical Band Saw (Vertical Band Saw).
a vertical band saw. A saw blade with a vertical line. Thare will rotate an cutting continues. a cut off light in all looks like a flat iron or steel may be lacking. Or cut into various shapes which The oTher saws can not.
a band saw different from saws seizures. The cutting are continuing. While Mills was responsible for cutting off only a stroke. a use of The saw blade are limited by a use of a centralized blade only.
The band saw blade has a thickness less than oar types of materials, resulting in a loss of less than
Vertical band saw. Provides several features to work. Similar to carve by hand. Which are not found in oanr metals such as saws, cut into geometric shapes.
4. Saw (Circular Saw or Radius Saw).
a circular saw. an circular saw is a saw blade with teeth around an band can be cut continuously. Often, some parts such as aluminum, can cut both The upright and tilted at an angle.
Security threat in an circular saw.
Saw a lot of harm. To cover up a saw.
Do not be impatient to exert control, overload cut.
First, a careful piece of work. Force because of lack of control a little easier to cut.
Always check an blade, but tough. Or stick a sharp saw.
No comments:
Post a Comment